Exception Errors | Windows95 | Errors |
Windows 95 Exception Errors - (Also see the Windows 98 Exception Errors page,)
There are several types of Error Messages : ( Click Here to see Errors listed individually by the Error Number )
- 00: Divide Fault -
The processor returns this exception when it encounters a divide fault. A divide fault occurs if division by zero is attempted or if the result of the operation does not fit in the destination operand
- 01 : Not Available
- 02: NMI interrupt -
Interrupt 2 is reserved for the hardware Non-Maskable-Interrupt condition. No exceptions trap through interrupt 2
- 04: Overflow trap -
The overflow trap occurs after an INTO instruction has executed and the 0F bit is set to 1
- 05: Bounds Check Fault -
The BOUND instruction compares the array index with an upper and lower bound. If the index is out of range, then the processor traps to interrupt 05
- 06: Invalid Opcode Fault -
This error is returned if any one of the following conditions exists:
- The processor tries to decode a bit pattern that does not correspond to any legal computer instruction.
- The processor attempts to execute an instruction that contains invalid operands.
- The processor attempts to execute a protected-mode instruction while running in virtual 8086 mode.
- The processor tries to execute a LOCK prefix with an instruction that cannot be locked
- 07: Coprocessor not available fault -
This error occurs if the computer does not have a math coprocessor and the EM bit of register CR0 is set indicating that Numeric Data Processor emulation is being used. Each time a floating point operation is executed, an interrupt 07 occurs.
This error also occurs when a math coprocessor is used and a task switch is executed. Interrupt 07 tells the processor that the current state of the coprocessor needs to be saved so that it can be used by another task
- 08: Double Fault -
Processing an exception sometimes triggers a second exception. In the event that this occurs, the processor will issue a interrupt 08 for a double fault
- 09: Coprocessor Segment Overrun -
This error occurs when a floating point instruction causes a memory access that runs beyond the end of the segment. If the starting address of the floating point operand is outside the segment, then a General Protection Fault occurs (interrupt 0D).
- 10 (0Ah): Invalid Task State Segment Fault -
Because the Task State Segment contains a number of descriptors, any number of conditions can cause exception 0A. Typically, the processor can gather enough information from the Task State Segment to issue another fault pointing to the actual problem. See Microsoft's Programming the 80386/80486 Guide for more information
- 11 (0Bh): Not Present Fault -
The Not present interrupt allows the operating system to implement virtual memory through the segmentation mechanism. When a segment is marked as "not present," the segment is swapped out to disk. The interrupt 0B fault is triggered when an application needs access to the segment
- 12 (0Ch): Stack Fault -
A Stack Fault occurs with error code 0 if an instruction refers to memory beyond the limit of the stack segment. If the operating system supports expand-down segments, increasing the size of the stack should alleviate the problem. Loading the Stack Segment with invalid descriptors will result in a general protection fault
- 13 (0Dh): General Protection Fault -
Any condition that is not covered by any of the other processor exceptions will result in a general protection fault. The exception indicates that this program has been corrupted in memory, usually resulting in immediate termination of the program
- 14 (0Eh): Page Fault -
The Page Fault interrupt allows the operating system to implement virtual memory on a demand-paged basis. An interrupt 14 usually is issued when an access to a page directory entry or page table with the present bit set to 0 (Not present) occurs. The operating system makes the page present (usually retrieves the page from virtual memory) and re-issues the faulting instruction, which then can access the segment. A page fault also occurs when a paging protection rule is violated (when the retrieve fails, or data retrieved is invalid, or the code that issued the fault broke the protection rule for the processor). In these cases the operating system takes over for the appropriate action
- 16 (10h): Coprocessor error Fault -
This interrupt occurs when an unmasked floating-point exception has signaled a previous instruction. (Because the 80386 does not have access to the Floating Point unit, it checks the ERROR\ pin to test for this condition.) This is also triggered by a WAIT instruction if the Emulate Math Coprocessor bit at CR0 is set
- 17 (11h): Alignment Check Fault -
This interrupt is only used on the 80486 CPUs. An interrupt 17 is issued when code executing at ring privilege 3 attempts to access a word operand that is not on an even-address boundary, a double-word operand that is not divisible by four, or a long real or temp real whose address is not divisible by eight. Alignment checking is disabled when the CPU is first powered up and is only enabled in protected mode
Specific Errors -
We've added a new section for Windows 95 Issues, Windows 98 Issues, ME Issues, Win2000 Issues and NT4 Issues. There you will find errors categorized by Keywords and by the source files such as VMM and VxD. You can also look in the Windows Exception Errors page.
|You are at the www.techadvice.com site which is not associated with the company or products shown on this page.|
© 1997,98,99,2000 www.techadvice.com All rights reserved