Conner Hard Drives

Please Note
1) For the latest specifications on these hard drives check go to the Seagate Web Site.
2) If your motherboard does not support drives larger than 1024 cylinders or you are not running in LBA mode, or you are not using a third party IDE program that allows using large drives, then do NOT enter a cylinder value greater than 1024.

Hard Drives Listing -

CFAxxx

• CFA1080A - 3.5" IDE Hard Drive, 1GB (1080 MB), 13ms access, RLL 1,7 encoding, (2097cyl. 16hd, 63spt, 2097 LZ, 0 WP) or (524, 64, 63)

• CFA1275A - Hard drive, 1.2gb, (2479 cyl, 16hd, 63spt), ( 2479cyl, 13hd, 63spt) or (619, 64, 63)

• CFA170A - (CP30174), 171MB, ( 332cyl, 16hd, 63spt)
• CFA270A - 270MB ( 524cyl 16hd 63spt ) (same jumpers as CFA170A)
• CFA2161A - 1023 64 63 (st32161a)
• CFA340A - 340mb. (665cyl, 16hd, 63spt)

• CFA540A - 1048 16 63 (524 32 63)
• CFA810A - 1572 16 63 (786 32 63) 
• CFA850A - 1652 16 63 (826 32 63) 

CFLxxx

• CFL350A - 905 12 63 
• CFL420A - 818 16 63 

CFNxxx

• CFN170A - 326 16 63 
• CFN250A - 489 16 63 
• CFN340A - 667 16 63  

CFSxxx drives

• CFS1081A - 524 64 63 
• CFS1275A - 619 64 63 
• CFS1276A - 524 64 63  
• CFS1621A - 786 64 63  (ST-31621a)
• CFS210A - 685 16 38 
• CFS270A - 600 14 63 
• CFS420A - 
  Hard Drive, 420mb, (826cyl, 16hd, 63spt)
  ...Master/Slave Selection Jumper Settings
  ...Single drive = Jumper pins 1-2
  ...Master drive = Jumper pins 1-2
  ...Slave drive = No Jumper pins 1-2

• CFS425A - 
  Hard Drive, 420mb, ( 839cyl, 16hd, 62spt ) or (839cyl, 16hd, 63spt)
  ...J1 closed - Single Drive/Master drive of 2 drives
  ...J1 Open - Slave drive of 2 drives
  ...J3 Open - Master/Slave controlled by J1
  ...J3 Closed - Master/Slave controlled by Cable Select

• CFS540A - 525 32 63 
• CFS541A - 599 28 63 (st-3541a)
• CFS635A - 619 32 63 
• CFS850A - 826 32 63 

CP-xxxx 

• CP2254 - 489 16 63 
• CP2034 - 411 4 38 
• CP2044/PK - 2.5" IDE Hard Drive, 42.9 MB, 19ms, RLL (2,7), (552cyl 4hd, 38spt) or ( 980cyl, 5hd, 17spt )
  Pin 1 located on the inside edge (next to the JP1 pins)
  ...Jumpers
  ...Single drive E1=closed
  ...Master drive E1=closed
  ...Slave Drive E1=Open
  ...JP1 is factory set to Open, E2 is not used.

• CP2064 - 823 4 38 
• CP2084 - 548 8 38 
• CP2088 - 548 8 38 
• CP2124 - 762 8 39 
• CP3000 - 980 5 17 
• CP30064 - 762 4 39 
• CP30064H - 762 4 39 
• CP30084e - 3800 rpm
• CP30084 - 3400 rpm Hard Drive, 84.5MB, 3.5" IDE, 19ms, RLL (2,7), ( 526cyl, 8hd, 39cpt ) or (1058cyl, 4hd, 39spt, Write precomp Automatic )
  ...Pin 1 located next to power plug
  ...Holding the drive with the connectors pointing down, the jumpers are at the top left area
  ... ...E1
  ... ...DSP
  ... ...C/D
  

Set Slave/Master Using Jumper C/D and DSP

• CP30084E - 903 4 46 
• CP30104 - 762 8 39 
• CP30104H - 762 8 39 
• CP30124 - 895 5 55 
• CP30174E - 
  Hard Drive, 170MB, (1806cyl, 4hd, 46spt) or ( 903cyl, 8hd, 46spt )
  ...Jumper C/D
  ... ...closed = single drive or master drive
  ... ...open= Slave drive
  ... ...pin one close to the large DC power connector

• CP30204 - 683cyl 16hd 38sec 
• CP3024 - 615 4 17 
• CP30254/H - 895 10 55 
• CP30344 - 665 16 63 
• CP3044 - 980 5 17 
• CP30544 - 1023 16 63 
• CP3104 - 776 8 33 
• CP3181 832cyl 6hd 33sec
• CP3184 - 832 6 33 
• CP3204F - 683 16 38
• CP3304 - 659 16 63
• CP3364 - 702 16 63 
• CP3504 - 987 16 63 
• CP3544 - 1023 16 63 

SCSI

• Model, Cylinders, Heads, Sectors
  CFA170S - 2111 2 79
  CFA340S - 2111 4 79
  CFA540S - 2805 4 94
  CFA540E - 2805 4 94
  CFA810S - 2794 6 94
  CFA850S - 3613 4 115
  CFN170S - 1339 4 61
  CFN250S - 1339 6 61
  CFP1060E - 2757 8 94
  CFP1060S - 2757 8 94
  CFP1060W - 2757 8 94
  CFP1080S - 3658 6 96
  CFP2105S - 3948 10 106
  CFP2105W - 3948 10 106
  CFP2107S - 3999 10 104
  CFP2107W - 3999 10 104
  CFP4207E - 3999 20 104
  CFP4207S - 3999 20 104
  CP2120 - 762 8 39
  CP30080E - 1806 2 46
  CP30100 - 1524 4 39
  CP3020 - 636 2 33
  CP30200 - 2124 4 49
  CP30340 - 665 16 63
  CP3040 - 1026 2 40
  CP30540 - 2242 6 79
  CP3100 - 776 8 33
  CP31370 - 2386 14 80
  CP3200(F) - 1366 8 37
  CP3360 - 1807 8 49
  CP340 - 788 4 26
  CP3500 - 987 16 63
  CP3540 - 1807 12 49

© 1997,98,99,2000 www.techadvice.com All rights reserved

---